Skip to content

Repairs checked for safety before you drive off

(559) 546-7716
(559) 546-7716
Technician working on a silver sedan with a crushed front end clamped to a red frame-straightening machine with pulling chains in a shop bay

ServicesFrame Straightening

Frame Straightening in Madera

A bent frame or unibody can hide under a car that looks fine. We measure your vehicle against the factory dimensions, pull the structure back where it belongs and check it again, so it tracks straight and protects you the way it was built to.

What frame straightening fixes

On most cars and crossovers there is no separate frame. The body shell itself, with its floor, rails and pillars, carries the load. Pickups and plenty of larger SUVs are different and sit on a ladder frame underneath. In both cases, a solid hit can push the structure a few millimeters off, and a few millimeters is plenty to cause trouble.

A car with a shifted structure may pull, wear tires unevenly or leave gaps around the doors and hood. The bigger issue is safety. Crumple zones, airbag sensors and seat mounts all depend on the body being where the engineers put it. If it is off, the car may not handle the next crash the way it should.

Our shop is I-CAR Gold certified, and we treat structural work as the most careful job we do. We measure before we pull, pull in small steps and measure again. You get your vehicle back square, not just looking straight.

What the work includes

Full structural measurement

We check key points on the underbody and upper body against the factory dimensions for your make and model. You see where it is off and by how much.

Controlled pulls

The vehicle is anchored at set points and pulled back in stages. We stop and re-measure between pulls so the metal is moved, not overworked or torn.

Damaged part replacement

Some rails, aprons and supports are made to be replaced, not straightened, once they kink. We follow the maker's repair steps on which parts must be swapped and how they are joined.

Suspension and mount checks

Strut towers, cradle mounts and suspension points get checked too. A frame that is straight with a bent control arm still drives wrong.

Post-repair measurement

When the pulls are done, we measure the whole structure again and keep the readings. Ask and we will walk you through them.

Front-damaged dark pickup on a tilted flatbed tow truck at a body shop's concrete lot as two workers look it over, with open repair bays behind

Signs your car may need frame work

It pulls after an accident
If the wheel is centered but the car drifts, or the wheel sits crooked going straight, something underneath may have moved. An alignment alone will not hold if the mounting points are off.
Doors, hood or trunk don't line up
Look for a gap that is wider at the top of a door than at the bottom, a hood corner sitting higher than the other, or a door that now needs a hard push to latch. That usually means the opening has moved, not just the panel.
One edge of a tire going bald
When the inside or outside of a tread starts disappearing in the weeks after a crash, a suspension mount may be bent or a rail may have shifted.
Creaks, rattles or wind noise
New noises over bumps, or a whistle at highway speed that was not there before, can come from panels and seals that no longer meet right.
Any hit hard enough to deploy airbags
If the airbags went off, the structure took real force. We measure every vehicle like that, even when the outside looks minor.

How a frame job runs at our shop

  1. 1

    Look and measure

    You bring your car in. We put it up, look underneath and take measurements before anyone touches a tool, so the plan is based on numbers.

  2. 2

    Written estimate

    We write up what we found line by line: what gets pulled, what gets replaced and why. If an insurance claim is involved, we send the same findings to the adjuster. Our Insurance Claims page covers how that part works.

  3. 3

    Straighten in stages

    The vehicle is clamped to the bench and pulled back in small moves. We re-measure after each one. If we open something up and find more damage, we stop and call you before going further.

  4. 4

    Rebuild and check

    With the structure square, we move on to any collision repair, bumper repair or paint and refinishing the car needs. Then we set the alignment and check that warning lights and sensors read normal.

  5. 5

    Final measurement and pickup

    We measure once more before you pick it up. You get the keys and a plain explanation of what was done.

What moves the price of a frame repair

No two structural jobs come out the same, so the price depends on what our measurements turn up on your car. We write the estimate after the vehicle is on the bench and measured, not from a photo. If we find more damage once parts come off, we call you before any added work starts.

How far the structure moved
A rail that is slightly out takes fewer pulls than one that buckled. The more it moved, the more bench time and measuring it takes.
Pull or replace
Structural parts that are kinked or cracked usually get cut out and replaced, then welded or joined the way the maker's repair instructions say. That means more parts and labor than a straight pull.
Unibody or body-on-frame
Unibody cars and full-frame trucks are set up and repaired in different ways, and each make has its own repair steps we follow.
What else was damaged
Suspension parts, sensors, panels and paint that took the same hit all add to the total. We list each one so you can see where the money goes.

Frame straightening questions

Is a car with frame damage safe to drive after it's fixed?
Yes, when the structure is measured back to factory dimensions and damaged parts are replaced the way the maker calls for. That is why we measure before, during and after. We will not hand back a car we would not drive ourselves.
Can every bent frame be straightened?
Not always. Some damage is too severe, or the maker says certain parts must be replaced instead of pulled. Sometimes the repair costs more than the car is worth, and your insurer may call it a total loss. We will tell you plainly what we see.
My car might have a bent frame. Is it okay to drive it in?
Have it towed if it pulls hard, grinds, leaks fluid or shows warning lights on the dash. If it feels normal on the road, it is usually fine to bring it over soon at easy speeds. Not sure which camp you are in? Call and tell us how it is behaving, and we will help you decide.
Will frame damage show up on a vehicle history report?
That comes down to how the accident and the insurance claim were reported, which is out of our hands. A good repair will not remove an entry that is already on file. What it does is put the car back in safe, measured shape. If a buyer asks later, we can explain the work we did.
How long will my car be in the shop?
It depends on how much moved, whether parts need replacing and how fast those parts arrive. We give you an honest time estimate with the written estimate and call you if it changes.
Gray sedan with freshly finished paint parked on a cracked concrete lot outside an open body shop bay, where another car sits masked for painting

Think your frame took a hit?

Tell us what happened and how the car is driving. We will explain what to look for and set a time to bring your vehicle in for a measurement and written estimate.